↑
All features

Everything it does

The whole list on one page, one line each. The main page explains the ideas, the user manual every setting, the build guide the hardware.

Auto mode

  • Starts in Auto, fan off, at every power-up: plug it in and ride.
  • Power, heart rate or both: follows whichever says you're working harder, or only one of them (Decide by, per rider); a missing one is covered by the other.
  • Your own numbers: the steps are set in % of your FTP and heart-rate range, so they fit a strong and a beginner rider alike, and read as training zones.
  • Up quickly, down slowly: smoothed power, so a short recovery doesn't switch the fan down.
  • No flapping: one level at a time, a gap between the up and down levels, a minimum time at each level.
  • Fan response: Calm, Normal or Quick, for how eagerly it follows you.
  • Stop pedaling: it holds a minute, then winds down to off; ride on and it carries on.
  • Sensor lost: runs on the other one; both lost: holds 2 minutes, then steps down.
  • Nudge − / +: up to two levels less or more for this ride; Auto still follows the workout.
  • Highest level: keep Auto at 1 or 2 for quiet evenings.
  • Heat from CORE: with a CORE body temperature sensor, heat strain 3 keeps at least level 2, 7 level 3, while you ride (per rider: on unless switched off, both values adjustable).
  • Idle off: off after 15 minutes (adjustable) without pedaling or sensor data.
  • Every threshold and time is a setting, with Reset to defaults.

More: Auto mode · How Auto decides

Sensors

  • Strap and trainer at once over Bluetooth: any heart-rate strap or armband, any trainer or power meter with Cycling Power or FTMS.
  • Either one is enough: power only, or heart rate only (rollers, a basic trainer).
  • Finds your sensors by itself and remembers them, so it never grabs the strap of the rider next to you.
  • Find sensors: a list of what's nearby with each one's signal, pick one; Forget to change. The chosen sensors show their name, connection and signal.
  • Reconnects by itself after a dropout.
  • Your training app stays connected to the same sensors (most allow two connections).
  • Passes your heart rate on (Share heart rate, off until ticked): for a strap that allows only one connection, the fan sends its heart rate on as a Bluetooth heart-rate sensor of its own, WattWind-XXXX HR, for one app or bike computer; one that pairs (Garmin Edge) pairs once, without a code, and reconnects by itself after a restart.
  • Strap taken off: noticed within seconds and shown as "(not worn)", even on straps that keep sending their last value; Auto then goes by power.
  • Sensor battery shown, with a warning at 15 % or less.
  • CORE body temperature sensor as a third sensor: core temperature and heat strain on the page, saved per rider; it gets your strap's heart rate if it has none; read from its signal when not connected.

More: Sensors

Riders

  • Up to 5 riders, each with their own FTP, heart-rate range, Decide by, fan response, step levels, heat levels, strap and CORE.
  • Switches by strap: straps only send while worn, so the fan picks whoever's strap is on, within about 20 seconds.
  • Or by hand: a rider chosen in the list stays selected until you choose again.

More: Settings → Rider

Also an ordinary fan

  • Off · 1 · 2 · 3 from the page, no sensors needed; the level stays until you change it, also after a ride.
  • Off timer: Off in 30 min, 1 h or 2 h, then it stays off.
  • Forgotten? After 8 hours in Manual (up to 24, or never) it goes back to Auto, which turns it off when nobody rides.
  • Back to Auto mid-ride continues from the current level, no sudden drop.

More: Also an ordinary fan · Buttons

Linked fans

  • Several fans, one ride: any number of WattWinds follow one leader over your home Wi-Fi.
  • Each at its own level: same as the leader, one higher, one or two lower, or its own Auto settings from the leader's heart rate and power.
  • One remote: the leader's buttons and off timer move every follower that follows its level.
  • Sensors stay free: followers don't use Bluetooth at all.
  • Leader gone: followers hold a minute, then step down to off.
  • Pairing in a minute: Pair a new fan on the leader, Follow on the other; Unpair all followers and Pair again when plans change.
  • Encrypted and signed: other devices on your network can't read or fake the messages.

More: Linked fans · manual

The phone page

  • Served by the fan itself: no app, no account, no internet; light and dark.
  • Works on older phones too: plain web code, made for iPhones from about iOS 13 and Android phones with Chrome from about 2019, and current browsers on a computer.
  • On the home screen it opens like an app.
  • Readable on the handlebars: a big level, the mode, what happens next, live watts, rpm and bpm, the demand and what decided it, sensor dots; with a CORE, core temperature and heat strain.
  • The fan's name in the header, so with several fans you know which one you're on.
  • Warnings when something needs you: a low sensor battery, heat strain in CORE's zone 4, a hot controller, damaged firmware files, a safe start.
  • Never loses your input: unsaved changes are marked, with Save and Undo, and it asks before you leave; a wrong value is marked at its field with what to change.
  • Lost contact is shown: values grey out, and after a restart the page finds the fan again by itself.
  • Built-in manual behind the ?, the same one as on this site.
  • Live demo: the fan's own page runs in your browser, with a made-up rider and the same Auto.

More: The phone page · The screen

Wi-Fi

  • At http://wattwind.local on your home network, with the IP shown for Android; give each fan its own name.
  • Its own network WattWind-XXXX when there's no home network, and the page opens by itself when you join it.
  • Find networks lists what the fan can use, strongest first.
  • Test Wi-Fi before switching: shows the address your router gives it, reports a wrong password at once, saves nothing.
  • Router gone (or slow after a power cut): its own network after 2 minutes, then back home by itself.
  • Fan control never depends on Wi-Fi.

More: Wi-Fi

Security and privacy

  • Your own password and PIN at the first setup: no fan keeps the published default.
  • Settings PIN for settings, Wi-Fi, updates, logbook and backups (the fan buttons too, if you like); each device asks once; wrong guesses are slowed down.
  • Signed updates over Wi-Fi: the fan accepts only updates signed by the maker of the firmware it runs. A fork or your own build goes on over USB once; from then on, that maker's signed updates work over Wi-Fi.
  • Websites can't reach it through your browser: it answers only to its own name and address, and takes commands only from its own page.
  • Your data stays home: no cloud, no account; the logbook keeps no heart rate or power; the only thing it asks the internet is the time.
  • Forgot the PIN? Plug it in and out three times, then a fourth time and leave it: new PIN, everything else kept.
  • Erase everything before you give it away.
  • Compared with ETSI EN 303 645, the consumer smart-device baseline, as a guide.

More: Security and privacy · Your data

Maintenance and diagnostics

  • Firmware update over Wi-Fi from the page: signature and every file checked first; if anything fails, nothing changes. The box stays closed.
  • Check for updates: one tap asks GitHub from your phone (not the fan) whether there's a newer version; or get an email from GitHub when one comes out.
  • Backup and restore of all settings, on this fan or another; passwords only if you choose.
  • Logbook: every start and why, every level change with its reason, Wi-Fi and sensor events, errors; about 4½ to 9 days of a busy fan.
  • Diagnostics file to download and send when asking for help.
  • Detailed recording: every second of a ride for 24 h, for a problem that's hard to catch.
  • A line at the bottom of Settings: version, running time, why it last restarted, Wi-Fi signal, chip temperature, sensor batteries.
  • Firmware file check at every start.
  • Restart from the page.

More: Settings → Maintenance · Troubleshooting

Shortcuts and home automation

  • A simple JSON API: everything the page does, other programs can do too.
  • iPhone Shortcuts and Siri: "Fan high" by voice or from the home screen.
  • Android: a home-screen button with a free HTTP shortcut app.
  • Home Assistant: the fan as a sensor and buttons in a dashboard, ready-made configuration included.

More: Shortcuts · The fan's API

Built to fail safe

  • Relays off first at every start, before anything else runs.
  • Both wires disconnected when the fan is off; one stuck relay alone can't keep it running.
  • Never two speeds at once: break-before-make, at most one change per 2 seconds.
  • Hardware watchdog: a program that stops responding restarts with the fan off.
  • Every part restarts on its own after an error; an error can't leave a relay stuck.
  • Settings checked at every start; a bad value goes back to its default.
  • Safe start: after three error restarts in a row it starts with default ride settings, so the page stays reachable for a fix.

More: Safety

The hardware

  • Your own 3-speed fan, up to 100 W (185 W with the bigger fuse); 230 V, 120 V untested.
  • One board, 16 through-hole parts, 65 × 82 mm, ordered online from one ZIP file.
  • Mains kept apart: 8 mm between mains and low voltage, a fuse, the wiring diagram printed on the back.
  • Tested without mains first: the relays click through every level on USB power.
  • A printed box made by a script: change a number and it rebuilds and checks its own fit; ready-made print files too.
  • Closed and labelled: lid screws from underneath, an engraved rating plate, no USB opening unless you want one.
  • Straps to the fan's stand with two cable ties; one cable to the fan.
  • Or your own box, with a list of what it needs.
  • About €70–80 in parts.

More: Build guide

Open

  • All of it published: firmware (MIT), board and box (CERN-OHL-P), site and docs (CC BY).
  • Change anything: plain MicroPython, a KiCad board, a Fusion script; your own firmware with your own signing key.
  • Tested on the computer: 500+ tests, including whole simulated rides and a real ride replayed second by second.
  • Measured on a real ride: the same power, heart rate and cadence as a bike computer, under a second later.

More: Under the hood · Measured